Jabsco Toilet Accessories
Outlet Non-return Valve
A non-return valve can be used to help prevent waste
backflow on electric toilets.
Simply fit discharge hose
close to the toilet.
| Price | Model | Description |
|---|---|---|
33.13 € |
58109-1000 | 1-1/2" (38mm) Outlet Non-Return Joker Valve |
Inlet Non-return valve
A check valve gives quicker and easier
flushing response on many manual and
37010 Series Electric Toilet installations.
For use with manual and electric toilets using sea water flush.
Simply fit inlet suction hose near seacock, but just above waterline.
Prevents loss of prime in above-waterline installations.
Retains water in bowl of 37010 Series Electric Toilets installed above waterline
| Fitting | Size | Weight |
|---|---|---|
| 3/4" (19mm) ID hose | 10.8cm x 5.5cm x 5cm | 0.1Kg |
| Price | Model | Description |
|---|---|---|
| 30.35 € |
29295-1011 | Inlet Non-Return Valve |
Y-valve
Robust Y-Valve for use in toilet applications. Allows waste to be pumped overboard or into a holding tank.
Rotating ports allow for variable routing of hoses onto the valve.
Can be operated through bulkhead by use of optional
handle extension.
Can be padlocked so that waste can only go to the holding tank to comply with some local regulations (padlock not included)
.Waste and corrosion-resistant construction throughout.
| Fitting | Size | Weight |
|---|---|---|
| two 1-1/2" (38mm) ports and 1" (25mm) inlet port | 20cm x 19cm x 12cm | 0.9Kg |
| Price | Model | Description |
|---|---|---|
| 118.71 € |
45490-1000 | Y-Valve |
| 15.55 € |
45500-1000 | Handle Extension Kit |
| 16.02 € |
45493-0000 | Replacement Handle |
| 0.00 € |
18753-0661 | Replacement Ports Kit |
| 28.17 € |
45488-0000 | Service Kit |
Vented Loops
An essential safety component on all inlet
and discharge plumbing of toilets installed below the static or heeled waterline.
Simple valve system ensures water cannot siphon over plumbing loops.
Available in three sizes for 1-1/2" (38mm), 1" (25mm) and 3/4" (19mm) ID hose.
Internal valve avoids need for external venting.
Molded in tough, corrosion-proof plastic.
| Fitting | Size (cm) | Weight |
|---|---|---|
| 3/4" (19mm), 1" (25mm) and 1-1/2" (38mm) ID hose |
3/4"=7.5x9.5x2.5 1"=12.5x19x4.5 1 1/2"=12.5x18.5x5 |
3/4" Model:(0.04kg) 1" Model: (0.13kg) 1-1/2" Model: (0.2kg) |
| Price | Model | Description |
|---|---|---|
| 44.96 € |
29015-0000 | 3/4" (19mm) model |
| 77.95 € |
29015-0020 | 1" (25mm) model |
| 64.41 € |
29015-0010 | 1-1/2" (38mm) model |
| 15.88 € |
29015-1000 | Replacement valve. Only available in Europe. |
Waste Pump
Robust diaphragm pump passes
solids and is particularly effective
in emptying holding tanks.
The
multi-positional pump head offers
a variety of installation options.
5 GPM (19 LPM) output.
Self-priming up to 10' (3m).
Capable of extensive dry running.
Compact and simple design.
Quiet running.
Flexible installation.
Corrosion-resistant parts.
Complies with USCG 183.410 and ISO 8846 MARINE (Ignition Protection).
ISO 8849 MARINE (Bilge Pump Standard).
| Fitting | Size | Weight |
|---|---|---|
| 1-1/2" (38mm) ID hose | 27.7cm x 15.5cm x 11.1cm | 2.7Kg |
| Price | Model | Description |
|---|---|---|
| 281.06 € |
50890-1000 | 12V DC, fuse 10 amp |
| 281.06 € |
50890-1100 | 24V DC, fuse 5 amp |
| 31.82 € |
SK890 | Service Kit |
Run Dry Macerator Pump
The latest version of the Macerator Pump now has a fully sealed motor and a new, more powerful chopper blade.
The sealed motor consists of O-ring sealed endbells, sealed bearings, and a hard, durable powder coating to prevent corrosion from occurring both internally and externally.
A new four-bladed chopper has been added to further reduce the possibility of clogging.
The pump still has the Run-Dry feature present in previous models.
Triple-sealed motor to prevent both internal and external motor corrosion.
New four-bladed chopper reduces clogging.
New stainless steel bolts.
Detects the absence of fluid then shuts off pump before impeller is damaged.
Sensor provides adequate run-dry period to allow initial priming of the pump.
Flow rate to 12 GPM (45 LPM).
Self-priming to 4' (1.2m) vertical lift.
Complies with USCG 183.410 and ISO 8846 MARINE (Ignition Protection).
| Fitting | Size | Weight |
|---|---|---|
| 1-1/2" (38mm) hose barb plus
1-1/2" (38mm) NPT Inlet port, Discharge Port: 1" (25mm) hose barb |
29cm x 12cm x 9cm | 2.3Kg |
| Price | Model | Description |
|---|---|---|
| 199.13 € |
18590-2092 | 12V DC pump, marine model |
| 212.92 € |
18590-2094 | 24V DC pump, marine model |
| 24.89 € |
17288-1000 | Replacement Bolt Kit |
| 85.41 € |
18598-1000 | Service Kit |
Toilet Pumpgard
The Pumpgard protects manual or electric
toilets from pump malfunctions caused by debris.
Simply installed in 3/4" (19mm) ID inlet hose.
Transparent housing allows instant inspection.
Screw-off top allows quick in-place cleaning and
removal of debris.
| Fitting | Size |
|---|---|
| 3/4" (19mm) ID hose | 12cm x 7cm x 6cm |
| Price | Model | Description |
|---|---|---|
| 28.07 € |
46400-0000 | Toilet Pumpgard |
| 17.12 € |
18753-0040 | Replacement 40# Mesh Filter |
Solenoid Valve for 37010 Series Electric Toilets
Where 37010 Series Electric Toilets are installed below the waterline,
we recommend installing a loop on the inlet plumbing rising at least 8" (20cm) above the highest (static or heeled) waterline level,
and installing a vented loop fitting at the top of the loop to stop water siphon over the loop and flooding the vessel.
The suction generated by 37010 Series Electric Toilets will open the valve in vented loops, drawing in air and preventing priming.
The 37068-2000 Solenoid Valve attaches directly to Jabsco Vented Loops and is wired to the toilet's on/off switch.
It closes whenever the toilet pump is operated and ensures full pump priming.
| Price | Model | Description |
|---|---|---|
| 98.02 € |
37068-2000 | Solenoid Valve for use with 12V or 24V DC, For use with the Following: |
| 44.96 € |
29015-0000 | 3/4" (19mm) Vented Loop |
| 30.35 € |
29295-1011 | Recommended Accessory: 3/4" (19mm) Inlet Non-Return Valve |