Go to Nuova Rade Site
Go to Marina del Sol Site
Go to Lofrans Site
Índice      Cart      Contact


Bilge Pumps Introduction

Rule Submersible Bilge Pumps have set the standard for the industry for decades.
They are the first choice of yachtsmen and fishermen throughout the world.
More innovations in bilge pump design have come from Rule Industries than any other manufacturer,
and we are proud to offer the broadest range of bilge pumps in the world.
Rule Industries has taken the initiative to once again set the standard.
We are moving forward to redesign our bilge pumps from the 360 to the 4000 GPH pumps.
As we look into the future, you will see new designs, more options and higher efficiencies.
FEATURES AND BENEFITS
Pump and switch are stand-alone products.
Compact, efficient, long-life motors.
Sizes: 360, 500, 800, 1000, 1100, 1500, 2000, 3700 and 4000 in 12, 24 and 32 volt versions.
Limited three-year warranty.
Ability to run dry for short periods.
Easy-clean, snap-lock strainer bases.
Stainless steel shafts.
Completely submersible.
Marine-grade blocked wiring.
Rust and corrosion protection.
Silent and vibrationless operation.
CE and ISO 8849 certification.
Ignition protection.
Traditional operation activated by a float switch and/or panel switch, providing an extra level of security and protection.
Remove the motor by pushing the side tabs, allowing easy access to clean the strainer and the impeller cavity.

Manual Diaphragm Pumps



These are the traditional mainstay of small craft bilge pumping systems
and can offer surprisingly good flow rates, as well as a variety of installation options.
Yacht racing rules state that at least one pump must be capable of being pumped from the cockpit with all hatches shut.
The best way to accomplish this is with a through deck kit,
which allows the pump to be installed safely below decks while the operator pumps from above.
A well-designed manual bilge pump is very hard to block due to its large bore hose and valves and one-piece diaphragm.
The larger pumps in Jabscos line of manual bilge pumps
are also suitable for ballast and waste transfer.


Electric Submersible Pumps



By far the most popular type of electric bilge pumps, submersibles give very high outputs,
are cost effective, have low amp draw and are easy to install.
They are designed to fit in the lowest part of the bilge and only require discharge pipework and electricity supply.
However, flow rates decrease as the discharge head increases, so check our recommended maximum discharge heads,
and if in doubt, always increase the size of the pump. Although our submersibles can be run dry for up to two hours,
pump life can be extended by avoiding dry running whenever possible.
All submersibles can be operated using a float or Hydro Air switch,
and remotely controlled outside the bilge compartment by using a Rule switch panel.


Electric Diaphragm Pumps

These pumps are excellent for shallow bilge boats, where the water left behind
by other types of pumps will slop from side to side.
With the small size of inlet plumbing, they are very effective as bilge pumps, removing all but the last drops of water.
Diaphragm pumps can be run dry, which removes the need to watch overboard outlets while the pump is running.
The ability to self-prime means they can be mounted in an easily accessible,
high and dry location to simplify installation and improve serviceability. Most models in the line are supplied
complete with a Pumpgard strainer to protect the pumps from bilge debris.


Electric Flexible Impeller Pumps



Flexible impeller pumps make excellent bilge pumps,
principally because of their ability to handle bilge debris without damage.
Because of the robust design, many owners still use our 12 volt DC or 24 volt DC flexible impeller motor pump units that are up to 25 years old!
Flexible impeller pumps also give the benefits of good flow, low cost, low size and weight,
and are easily serviced and maintained. Most flexible impeller pumps must not be run dry,
as this will damage the impeller and require replacing. However, the Utility Puppy 2000 and 3000 both allow a maximum of 10 minutes dry running after initial prime.
Flexible impeller pumps can be operated using a float or Hydro Air switch,
and remotely controlled from outside the bilge compartment. There is a wide range of flexible impeller pumps to choose from,
giving a range of flows, discharge heads and self-priming options for applications such as ballast transfer,
bait tank circulation and deck wash duties.




Engine Driven Flexible Impeller Pumps



Jabsco Engine Driven Pumps are probably the strongest and most reliable pumps produced today.
Combined with other benefits such as selfpriming and very high flow rates,
these pumps are now the firm favorites of commercial and professional mariners worldwide.
All the pumps are easily maintained and can fulfill a variety of duties onboard both modern and classic vessels.
Jabsco engine driven pumps come in a very wide range of performances and sizes, and can be direct driven by a clutch,
pulley or hydraulic drive, or close coupled to a suitable power take-off on the engine.
These pumps are suitable for applications such as:
High-flow, heavy-duty bilge pumps.
Emergency onboard bilge pumps.
Firefighting pumps.
Engine cooling.
Water ballast transfer.
Circulation duties.


Of course, each application requires different features from each pump and drive type.
Either manual or electromagnetic flexible impeller clutch pumps are ideal for bilge pumping.
Each type of clutch has different benefits from the other.
Manual clutches will operate as long as the engines are still running,
which provides added security when operating as an emergency bilge pump.
Electromagnetic clutches can be operated remotely via float or Hydro Air switches,
while fitting a vacuum switch eliminates all risk of dry running damage.
However, electromagnetic clutches will only engage as long as electrical power remains available.



Tel: (34) 952 802643

Email: mail@mds-nautica.com

Marina del Sol de Estepona SA

Plaza de Levante 35/37

Puerto Deportivo

Estepona 29680

Malaga España

Tel: (34) 952 802643

Email: mail@mds-nautica.com